Online:
Visits:
Stories:

By Gun Watch (Reporter)
Contributor profile | More stories

Story Views
Now:
Last Hour:
Last 24 Hours:
Total:

3D Imura Hybrid Revolver 2.0 printed, Test Firing Soon

Sunday, May 10, 2015 20:49

% of readers think this story is Fact. Add your two cents.

(Before It's News)

An Imura revolver, 2.0 has been designed by that intrepid 3D engineering designer, Wayfairy. He had to redesign the system, but the prints have been done and the prototype has passed the basic, non-firing function tests. From 3dprint.com:

One particular member of the community, known as ‘Wayfairy,’ has taken a particular interest in the Imura story. In fact he has set out to create a 3D printable gun honoring the incarcerated gun manufacturer, called the ‘Imura Pistol.’ Basically what he has done is take the original .38-caliber Zig-Zag revolver that had led to Imura’s arrest and revised it, making several key changes, designing a new gun from the ground up.

The major question is whether it will withstand the tensile forces that tend to separate the cylinder from the barrel and drive the case to the rear.

As you can see, the design is a hybrid, using metal tubing and 3D printing, that takes advantage of some of the best of both materials and technologies.

The gun itself uses .22 long rifle ammunition, and a .225″ ID 316 or 308 stainless tubing from McMaster. As for its appearance, just take a look at some of the images above and below. It’s a masterpiece in our opinion, and the only question left to be answered is whether or not it will actually fire a bullet without exploding in one’s hand.

As I wrote in September of 2014:

I see one weakness that the designers have probably noticed. There is very little tensile strength in the proposed design. Convention revolvers use a metal frame to contain the forces generated by firing a charge. The chambers contain the pressure at right angles to the barrel, but the frame, chamber, and case, if one is used, must contain the pressure to the rear. The projectile contains the pressure to the front, where the force is used to propel it out the end of the barrel.

If I were designing this revolver, I would consider the use of a bolt as a center pin for the cylinder to turn on. A simple backplate of steel could be made to screw the bolt into, adding tensile strength. It would not need to be circular, as long as it supported the rear of the chamber being fired. Removal of the bolt would allow the cylinder to be removed from the side of the design, so as to facilitate loading. Many conventional revolvers use this design feature.

Wayfairy did not use my free advice, but it is possible that the ABS plastic used will have sufficient tensile strength to fire a few shots. The potential points of failure that I see are; cracking of the ABS backing plate at the firing pin hole, and cracking of the lower split hinge.

If that occurs, there are fairly easy design fixes. A properly sized steel washer could be inserted between the backing plate and the rear receiver. Make the washer just big enough so as to not quite reach the firing pin hole and it would not need any machining. That would likely solve cracking of the backing plate.

If the lower split hinge cracks, it should be possible to increase its diameter by 2X, or even 3X, which would increase the tensile strength by 4-9 times. If that were insufficient, my original suggestion of a center – pin made from a steel bolt would greatly increase tensile strength of the design. There seems to be plenty of room in the cylinder for this, if it is necessary.

I would have no qualms about test firing this revolver, given a few safety considerations. I would wear gloves and ballistic eye protection, and hearing protection.

As the people creating this interesting revolver are intelligent, they will likely function fire the prototype with primed casings, to insure ignition. In my first firing test, I would use Aguila Colibri .22 cartridges. It is likely that this design will have sufficient strength for them. They could move forward from there to destructive testing if they like, with more and more powerful .22 cartridges. The Colibri cartridges would be proof of principle, and would make a wonderful YouTube video with popping balloons or smashing Oreo cookies at a yard or two. They are as powerful as many air rifles.